Standard Installation Scope

All standard installations are carried out by fully NZ-trained, qualified, and registered tradespeople. Relevant Gas Safety Certificates (GSC) and Electrical Certificates of Compliance (CoC / ESC) are issued for all applicable installations.

What Standard Like-for-Like Installation Means:

Included: Delivery, positioning, levelling, securing, connecting to existing compliant utilities, testing, commissioning, and optional removal/disposal of your old like-for-like unit.

Excluded: Cabinetry alterations, benchtop cutting or enlargements, switchboard upgrades, running new wiring runs, plumbing/drainage alterations, ducting/venting modifications, and structural or decorative repairs.

Replacement Unit Rating: The new replacement appliance must have an electrical wattage/amperage rating or gas MJ/h consumption rating that is identical or equivalent to the unit being replaced. Upgrades to higher-draw appliances (e.g. switching from a low-draw standard ceramic cooktop to a high-capacity induction cooktop) that exceed existing circuit, breaker, or cable capacities are not covered by standard installation and will require additional circuit upgrade works quoted separately.

Indicative Rates for Common Non-Standard Remediation:

Any additional work identified on site that falls outside the standard scope will be quoted transparently prior to work commencing.

Replacement single oven/hob switch: $65.00 incl. GST
Replacement double oven/hob switch: $85.00 incl. GST
Faulty or incorrect specification circuit breaker replacement: $75.00 incl. GST
Full replacement of damaged oven connection (socket and cord set): $265.00 incl. GST
EV Charger cable runs exceeding 5 metres: $50.00 incl. GST per additional metre

Inclusions: Positioning into existing allocated space, connecting to existing standard power socket, levelling, and operational testing.

Exclusions: Cabinetry alterations, electrical socket or wiring modifications, and plumbing for ice/water dispensers where no existing compliant valve exists

Pre-condition: Existing power point and space must be safe, compliant, and correctly sized.

Inclusions: Installation into existing allocated cavity, connecting new inlet and drain hoses to existing adjacent plumbing and waste connections, connection to existing power socket, levelling, and operational testing.

Exclusions: Cabinetry alterations, modification of existing plumbing or waste pipes, and electrical upgrades or socket relocation.

Pre-condition: Existing plumbing valves, waste trap spigots, and electrical points must be accessible and in compliant condition.

Inclusions: Positioning into existing allocated floor/bench space, connection to existing standard power socket, levelling, and operational testing.

Exclusions: Wall mounting / bracket installation, external venting installation, ducting extensions, or structural penetrations.

Pre-condition: Existing electrical services must be safe and compliant prior to installation.

Inclusions: Mounting into existing allocated space with compliant clearances, connecting to existing electrical supply, securing, and testing.

Exclusions: Installation, replacement, extension, or modification of ducting or external flues; cutting into ceilings, soffits, scotia, walls, or cabinetry; plaster repairs, painting, or decorative making good.

Pre-condition: Installation is subject to manufacturer clearance requirements; existing electrical supply must be compliant.

Inclusions: Fitting into existing allocated benchtop cutout, connection to existing compliant electrical supply, sealing, securing, and operational testing.

Exclusions: Enlarging or modifying benchtop cutouts, benchtop/cabinetry structural work, and running new sub-circuits from the switchboard.

Pre-condition: Existing electrical supply must be safe and compliant.

Inclusions: Fitting into existing allocated benchtop cutout, connecting to existing compliant gas supply point (including new approved flexible hose where required), connecting to existing electrical point for ignition, gas soundness testing, and commissioning.

Exclusions: Benchtop cutout modifications, gas pipework extensions/rerouting, installing new isolation valves or bayonet fittings, and changing supply pressure regulators.

Pre-condition: Existing gas and electrical services must be safe and compliant.

Inclusions: Mounting into existing allocated cabinet cavity, connection to existing compliant electrical supply, securing, levelling, and operational testing.

Exclusions: Cabinetry modification or enlargement, wiring extensions, and sub-board upgrades.

Pre-condition: Existing electrical supply and cavity dimensions must be compliant and suitable.

Inclusions: Positioning into existing freestanding space, connection to existing compliant electrical isolator/supply, levelling, and operational testing.

Exclusions: Supply or replacement of broken appliance cord sets/plugs (quoted separately), cabinetry alterations, and wiring upgrades.

Pre-condition: Existing electrical services must be in safe, compliant condition.

Inclusions: Positioning into existing allocated space, connecting to existing gas supply and standard power socket, new approved flexible gas hose where applicable, jet conversion if required, gas soundness testing, and operational commissioning.

Exclusions: Supply or replacement of broken electrical leads/plugs, gas pipework alterations, new bayonet fittings, and running new gas supply lines.

Pre-condition: Existing electrical and gas services must be in safe, compliant condition.

Note: Final price subject to site inspection.

Inclusions: Isolating, disconnecting, and removing existing electric or gas hot water cylinder/califont; positioning heat pump on a standard base slab in an accessible outdoor location (strapped and secured to code); standard pipework and required valve kit connections to existing hot/cold services; condensate drain connection to existing drainage point; 1 x dedicated 20A electrical circuit from switchboard (including IP-rated isolator); testing and commissioning.

Exclusions: Switchboard upgrades or sub-mains capacity improvements; civil groundworks, non-standard concrete pads, retaining walls, or new drainage infrastructure; structural penetrations, roof work, wall repairs, or painting; gas main alterations beyond direct appliance disconnection.